2 ingl. some reasons as that stated on a different

2_ingl. SOME REASONS AS THAT STATED ON a DIFFERENT SUBJECT ВЛАДИМИРОМ not. КРЫЛОВИЧЕМ CONCERNING And WITHOUT IT.
STILL SOME ХИРОСТИ.
That can strongly facilitate work, as carver, and with wood.
If that - that to speak, yes ушами_Acoustical petals on a head_ to move - will understand, други шо_friends is you, I shall tell to you ищщо plus too plus_! - осинова -an aspen an aldera board, for a groove that is good, хуть_ it is_ кудринской of a groove with list , that in кудряшках__a bend in a groove_ from foliage! And mouth разините__To open strongly mouth_! Though the aspen all Is soft - there will be for Geometrical she(it).
Time a groove have understood - you, is more best get accustomed!
HOW TO CUT the HANDLE?
Half here is cut out, and in what a secret with Второю половиною_still secret_? Business that лобзик__The manual tool for a groove on a twisting line-_ yours should Cut All For time!
ОКУДА _THE START_TO CUT TO BEGIN?
Having begun from Edge(territory), with a Side that is - you половинку_1/2 a groove on a twisting line-__ will not cut on conscience - the framework at лобзика - __ The manual tool for a groove on a twisting line-_ __поглядь ка __see it!_will be rested! Having begun FROM ABOVE, as yours here will not be gone, the work means,! And yours пропил __ a groove on a twisting line-_will pass FOR IS UNIFORM of TIME, that I and did(made) many times.
THAT - BASIC FORM of the HANDLE.
- you the answer mine, почемучки_ The man specifying there are a lot of questions_! In what cunning? Пилка__ manual tool for a groove on a twisting line-_, the cloth at лобзика__ manual tool for a groove on a twisting line-_ does not love when it(him) take out, extending from пропила_ a groove on a twisting line-_,_. At this moment the cloth is usual is torn! As a rule on such work there is one cloth, sometimes it(him) suffices on two, three such preparations. Besides it depends on thickness of preparation and hardness of a tree! And the CRUDE board пилется is much more difficult than well dried, лобзиком, it is natural. After the preparation is cut I at once I process her(it). First of all by jamb срезается фаска _cut _from both parties of a board and its(her) radius reaches 10 mm, that is боковина _ both parties of a board _on section comes nearer to radius. Though it is possible фаски _ both parties of a board _to cut and smaller radius.
PROCESSING.
It you will find in the literature, but do not use for processing files. They will be driven by a wooden dust or pitch if it is a birch, for example, you nothing добьетесть_do it not_. The tree processing on this Is concrete preparation so, that I on each side was passed наждачной_ grinding_ by a paper curtailed(turned) in a roll. On it there are about 10 minutes!
APERTURE FOR a suspension BRACKET.
For a board, that моется _ wash_also is cleaned it is not necessary to do(make) what that fastening of metal! It is not necessary to do(make) that that like a loop of their wire and drive in it(him) in the handle, as well as it is not necessary to do(make) a suspension bracket from тонокого of iron - such as the cut out rectangular of their can! Even that such suspension bracket will scratch a table, and circle or the plate on a board will shake. Always and long since in the handle drill an aperture and прожигают_ by his(its) piece of a nail of the a little bit greater diameter. It is possible to heat up on a gas cooker up to red каления__color of temperatura. Perhaps it is all secrets, that it is necessary to know at manufacturing such preparation, and still - this board was planed NOT LENGTHWAYS, and under a corner to an axial line, differently pure(clean) surface to not receive. And still - I cut  after she(it) about one year dries in a shadow, and only before a groove the layer in one is removed, two millimeters - will be lower Мягкаядревеситн, soft wood _besides at planing dried up wood will not be having chopped off, вырывов --__ deep deepenings in a surface _from a plane of a board, and rather deep.